Lexus RX 300
+ Lexus RX-300 cars
+ Administrations and methods of operation
+ Placing and regular maintenance of the car
+ Motor
+ Cooling systems of the motor, heating, ventilation and air conditioning
+ A system of provision of power and production of the carried out gases
+ Systems of electric equipment of the motor
+ Automatic exchange and differential interaxal
- Transmission line
General information
Removal and installation of the driving axle
Removal, desmontagem, meeting and installation of advanced ends of power
Removal, desmontagem, meeting and installation of rear ends of power
Substitution of a rear advanced epiploon of differential
Side substitution epiploons of differential bottom
Removal and installation of the rear case of differential, desmontagem of differential
+ Brakes system
+ Support of the triangular form of interruption and direction
+ Body
+ Electric side equipment
+ Schematic diagrams of electric connections
|
Removal, desmontagem, meeting and installation of rear ends of power
Removal and installation
Component of an end of rear power
|
|
- Withdraw corresponding rear wheels.
- Result two pins and withdraw behind the section of a tube of leak together with the placing.
- A pin results and withdraw the sensor of speed ABS.
- Take a pin, take away the hat of fixation and a nut results stupichny.
- Apply etiquettes in case of the hinge tripodny and in a flange of the differential bottom.
- Result 4 nuts, withdraw lavadores and desconecte an end of power of the differential one.
- Withdraw an end of power of the bearer.
- The installation is done upside-down. Hold tight the fixation with the necessary efforts, after the usefulness of check of installation of the functioning of sensors ABS, and also check and if necessary agreement the angles of the installation of rear wheels.
|
|
Desmontagem
|
|
- Ends of power of check:
- The extern hinges must not have play of excessively big side;
- One secures of the smoothness of the movement of the internal hinge in the direction of a support;
- One secures of the lack of the play of excessively big side of internal hinges in the radial direction;
- Check protective shelters of the existence of damages.
- Through the screwdriver they withdraw collars of protective coverings of hinges.
|
|
- Apply etiquettes in case of the hinge tripodny and in a power end and withdraw the case of hinge of an end of power.
|
|
|
Do not use a chisel to draw etiquettes. |
|
|
- Withdraw a ring of lock and apply etiquettes in the hinge tripodny and in a power end.
|
|
|
Do not use a chisel to draw etiquettes. |
- Lower the hammer and a pig from the gentle metal to hinge tripodny of a power end.
- Withdraw protective coverings with collars.
- The extern hinge is not subject to the desmontagem.
- Fix an end of power in a vice with gentle sponges and through the screwdriver and the hammer they lower a boot n ° 2 of an end, trying not to damage the rotor of sensor of speed ABS.
|
|
Do not damage the rotor of sensor of speed ABS. |
|
|
Meeting
|
|
|
|
- Napressuyte a new boot n ° 2 in an end.
|
- Temporarily establish new coverings of hinges with collars.
|
|
Before the installation of openings of wind of protective coverings of an end of power with a vinyl they carve to prevent his damage. |
- Place in a power end to hinge tripodny a conical part to the extern hinge and etiquettes of agreement of level of the hinge.
- Napressuyte to hinge in a power end through the hammer and a pig from gentle metal. Establish a ring of lock.
- 180 fills out a covering of the internal hinge ÷ 190 of yellow lubricant, etiquettes of agreement of level of the case of the hinge and fix the case to a differential one.
- 107 fills out a covering of the extern hinge ÷ 117 of the gray lubricant.
|
|
- One secures that the coverings enter in grooves in the driving to an end and they do not put out with a length standard of an end.
|
- Fix protective coverings for collars, when the screwdriver held tight them.
|
|
|
|
