LEXUS RX 300

1998 - 2003 of launch

Repair and operation of the car


Lexus RX 300
+ Lexus RX-300 cars
+ Administrations and methods of operation
+ Placing and regular maintenance of the car
+ Motor
+ Cooling systems of the motor, heating, ventilation and air conditioning
+ A system of provision of power and production of the carried out gases
+ Systems of electric equipment of the motor
+ Automatic exchange and differential interaxal
+ Transmission line
+ Brakes system
- Support of the triangular form of interruption and direction
   General information
   + Dispatch the support of the triangular form of interruption
   + Support of the triangular form of subsequent interruption
   + Direction
   - Geometry of support of the triangular form of interruption
      The angles of installation of wheels of the car - the general information
      Check and adjust of angles of installation of advanced wheels
      Check and agreements of angles of installation of rear wheels
+ Body
+ Electric side equipment
+ Schematic diagrams of electric connections
8ca8824c 726897-B21 на http://www.server-world.ru.
На www.finansy.ru банкротство юридических лиц последствия для директора.
нетканое полотно купить

Check and adjust of angles of installation of advanced wheels

To check

The control of geometrical parameters of a support of the triangular form of interruption happens in the special bookcase in the conditions of a workshop of the service of the car. The data of check and agreement of wheels are supplied in Specifications of the Chief Podvesk and direction.


 ORDER OF REALIZATION

  1. Distances of measure of the land to the center of an advanced pin of fixation of the lowest lever of an advanced support of the triangular form of interruption and to the center of an advanced pin of fixation of the longitudinal lever of a rear support of the triangular form of interruption. Compare the values received with demands of Specifications of the Chief Podvesk and direction.

They give to Heads Podvesk when it was given in Specifications and direction of tires P225/70R16.

  1. Install the car in the bookcase of measuring and check corners of the disorder, a vybeg and an inclination of an axle of the turn of wheels. If in normal corners of disorder of a vybeg and an inclination of an axle of the turn of wheels are not adapted with demands of Specifications of the Chief Podvesk and direction, check component of support of the triangular form of interruption the existence of damages and use.
  1. Check the convergence of wheels.
  1. The turn against the stop a steering-wheel and measure limits angles of the rotation of wheels. In unsatisfactory results of the check they check lengths of the left and right sketches of direction.

Disorder agreement

After the agreement of the disorder they check the convergence of wheels. In the agreement of a corner of the disorder they try to expose his middle value.


 ORDER OF REALIZATION

  1. Remove advanced wheels and bearers of sensors of the speed of ABS.
  2. Give two nuts lower of the fixation of a torture of a support of the triangular form of interruption advanced to a rotary fist.
  1. Polish a woodcarving of nuts (1) and (2) oils of reason and temporarily establish them.
  1. Adjust the pressing of disorder or the delay of the lowest part of a torture in the corresponding direction.
  2. Hold tight nuts with the effort of 210 nanômetros. Establish advanced wheels.
  3. Again check a corner of disorder.
  4. The variety of the agreement of the established pins does of 6' to 30'. If necessary it is possible to catch pins of agreement according to the table supplied down.

  1. After a nuts otdavaniye they substitute a pin (pins) in the bunch (if necessary).

Convergence agreement

 ORDER OF REALIZATION

  1. On protective coverings also hints countersows give of directing sketches.
  1. Become sketches of direction in the quantity of turns necessary for the installation of the middle value of specification of the convergence.
  1. It is secured what the residual lengths of the right and left sketches of direction do not differentiate any more, of what in 1,5 mm.
  1. Hold tight countersows of hints of directing sketches with the effort of 74 nanômetros. Also establish protective coverings.