LEXUS RX 300

1998 - 2003 of launch

Repair and operation of the car


Lexus RX 300
+ Lexus RX-300 cars
+ Administrations and methods of operation
+ Placing and regular maintenance of the car
+ Motor
+ Cooling systems of the motor, heating, ventilation and air conditioning
+ A system of provision of power and production of the carried out gases
+ Systems of electric equipment of the motor
+ Automatic exchange and differential interaxal
+ Transmission line
+ Brakes system
- Support of the triangular form of interruption and direction
   General information
   - Dispatch the support of the triangular form of interruption
      Removal, desmontagem, meeting and installation of a nave and rotary fist
      Removal, demolishing meeting and installation of a torture of a support of the triangular form of interruption
      Removal and installation of the lowest lever of a support of the triangular form of interruption
      Check and substitution of a spherical support of a support of the triangular form of interruption
      Removal, installation and check of the stabilizer of a support of the triangular form of interruption
   + Support of the triangular form of subsequent interruption
   + Direction
   + Geometry of support of the triangular form of interruption
+ Body
+ Electric side equipment
+ Schematic diagrams of electric connections
8ca8824c

Dispatch the support of the triangular form of interruption

Removal, desmontagem, meeting and installation of a nave and rotary fist

Removal and installation

Component of installation and meeting of a nave and rotary fist

1 - the Torture of an advanced support of the triangular form of interruption
2 - the Tip of directing the sketch
3 - Sensor of speed of ABS
4 - Meeting of a rotary fist and a nave of a wheel
5 - the Power end
6 - the Brake support
7 - the Brake disc
8 - the Quiff
9 - the Fixation hat

10 - the pin of Stupichny
11 - Nizhny Novgorod to lever of support of the triangular form of interruption
12 - the Boot
13 - the Load
14 - the Lock ring
15 - the Rotary fist
16 - the Protection covering
17 - a wheel Nave


 ORDER OF REALIZATION

  1. Withdraw an advanced wheel.
  2. Measure a play of axial side of the load of pressure of an advanced wheel and an axial thrashing of a nave. With this finality previously withdraw a support of brake and a disc of brake (the Head sees the System of brakes).

Confiantemente ties a support so that it was not bent and the hose of flexible brake was not loaded. Compare when they resulted from measurements to demands of Specifications of a Chief Podvesk and direction and if necessary the pressure load substitutes. Establish at the place a disc of brake and a support.

  1. Take the quiff of a countersow of an end of power and, having held tight it had been a pedal of brake, a countersow results.
  2. Withdraw a support of brake and a disc of brake (the Head sees the System of brakes).

Confiantemente ties a support so that it was not bent and the hose of flexible brake was not loaded.

  1. There results the fixation of the sensor of the speed of ABS and the bearer of his electrical system.
  2. One weakens, two nuts of the fixation are resistant supports of the triangular form of interruption to a rotary fist.

Still do not take pins.


  1. Take the quiff of a nut of a tip of directing the sketch, a nut results and through the special adaptation desconectam a tip of directing the sketch of a rotary fist.
  1. A pin and two nuts result and desconecte a spherical support of the lowest lever of an advanced support of the triangular form of interruption.
  2. Completely result two pins of the fixation of a torture of a support of the triangular form of interruption to a rotary fist and withdraw the meeting of a rotary fist with a nave.

Do not damage the covering of protection and a rotor of the sensor of the speed of ABS.

  1. The installation is done upside-down. After installation check a sign of the sensor ABS.

To be demolished and meeting

 ORDER OF REALIZATION

  1. A boot takes the screwdriver.
  1. Take the quiff of a nut of the fixation of a spherical support, a nut results and through the special adaptation they withdraw a spherical support of a rotary fist.
  1. Withdraw a nave through the special adaptation.
  1. Vypressuyte an internal bearer (on the outside) the pressure load.
  2. Result 4 pins and withdraw the covering of protection of a rotary fist.
  3. There takes a ring of lock and a vypressuyta the load of pressure of a rotary fist.
  1. If necessary it withdraws pins of nave through the special adaptation. The pins installation is done corseting itself of a nut.
  1. The meeting is done upside-down. Delay connections with the necessary efforts. During the installation of a boot they level an opening in him (for the sensor ABS) with an opening in a rotary fist. Use the new load of stupichny and the new quiff of a nut of the fixation of a spherical support.