LEXUS RX 300

1998 - 2003 of launch

Repair and operation of the car


Lexus RX 300
+ Lexus RX-300 cars
+ Administrations and methods of operation
- Placing and regular maintenance of the car
   General information
   General information on placing and agreements
   Time-table of regular maintenance
   Check of levels of liquids, control of holes
   Check of a condition of tires and pressure of his evaluation, rotation of wheels
   Substitution of filter of oil of reason and filter of oil
   General checks of the system of brakes
   Check and substitution of the filter of hall of a heater and to / in
   Check of a state and substitution of hoses of a compartment of reason, location of holes
   Check of a state and substitution of belts of the walk of auxiliary unities
   Substitution of the element of purifier of air of filtration
   Check of a condition of system of production of the carried out gases
   Check and substitution of captures of spark
   Substitution of fluid of brake, extraction through bomb of the system of brakes
   Check of a condition of component ones of a support of the triangular form of interruption and direction
   Check of a condition of protective coverings of ends of power and hinges of the driving axle
   The check of the operabilidade of there illuminate fixations, horn and supporter of a heater
   Check of the system EVAP
   Check of a state, agreement and substitution of brushes from clothes to rub of fabric
   His check of a condition of the battery and care
   Substitution of the cooling of liquid (CL)
   Check and adjust of slits valvate
   Check and adjust of the course of pedals of the work and parking brake
   Check of boots of the brake of parking
+ Motor
+ Cooling systems of the motor, heating, ventilation and air conditioning
+ A system of provision of power and production of the carried out gases
+ Systems of electric equipment of the motor
+ Automatic exchange and differential interaxal
+ Transmission line
+ Brakes system
+ Support of the triangular form of interruption and direction
+ Body
+ Electric side equipment
+ Schematic diagrams of electric connections
8ca8824c

Check of a state and substitution of belts of the walk of auxiliary unities

Check of a state

The too low tension of a belt leads to his increased use or I fail bystry. In the too high tension there can be damages of loads of the unities given by this belt. It is necessary to check periodicamente a condition of a belt, and in the moment of the detection of defects, to substitute a belt.

 ORDER OF REALIZATION

  1. The fingers walk in the whole length of a belt, feeling it in existence of slits and stratification. Also check if it is not present in a belt of atritos and sieges, zapolirovanny to polish. The belt must examine from two sides that the necessity means of what one supports. One convinces of passage of the lack of a rust, slits and agnails in pulleys. In a surface of work of an existence of belt of superficial perpendicular slits it is allowed. If these slits not to exceed the limits of an edge and not really deeply, to substitute a belt is not need.
I use edges of edges of a belt of driving
Angry slits (D) of a reverse side of a belt and descascamento of edges (E)
Razlokhmachivaniye of edges of side (F), split (H) and descascamento of side edges (G)
Edges separation (J), split (K)
  1. One secures of the fairness of the provision of a belt in pulleys.
  1. Check a tension of the driving of belts through the special adaptation and compare the results received with demands of Specifications of the Chief Nastroyki and regular maintenance of the car.

The tension of a belt of the walk of the compressor K/V and creator must happen in the siege between them.

Substitution

When it substitutes a belt of new multibackbone it will be the same size, as well as old man. During the installation of a new belt it is necessary to pay the attention on which the belt borders estreitamente to pulleys and does not move about his end faces. If the multibackbone belt is withdrawn not for aims of his substitution, remember or observe the direction of his movement that soon will establish a belt for the correct party.


 ORDER OF REALIZATION

  1. Give the pins with hinges and they fix of a belt of the walk of the creator and compressor К/В. An agreement pin weakens a tension of belt and take away a belt.
1 - the pin with Hinges
2 - the Fixation pin
3 - the Agreement pin
  1. Establish a new belt of the walk of the creator and compressive K/V in the sequence, the return to the removal. Check a tension of belt.
  2. Give hinged pins and they adjust of a belt of the walk of the bomb GUR and take away a belt.
1 - the pin with Hinges
2 - the Agreement pin
3 - the support of the triangular form of Agreement
  1. Establish a new belt of the walk of the bomb GUR in the sequence, the return to the removal. Check a tension of belt.
  2. The proceedings of the removal and the substitution of a belt of the walk of the bomb GUR supply with themselves in the Removal of Section e an installation of the bomb GUR and his belt of driving.